Magpul Industries M-LOK Bipod Mount Fits M-LOK Hand Guards Black Finish

Product Description

The Magpul Industries M-LOK Bipod Mount Fits M-LOK Hand Guards Black Finish is an adapter that installs into M-LOK slots to accept Harris-style bipod studs. It eliminates the need for Picatinny rail sections when mounting a bipod.

This mount brings bipod attachment points directly to your M-LOK handguard. It works with any bipod that uses the standard Harris swivel stud interface.

The black finish integrates cleanly with most handguard colors. Shooters who want a streamlined rifle setup use this mount to keep weight and bulk to a minimum.

Key Facts

• Product Name: Magpul Industries M-LOK Bipod Mount Fits M-LOK Hand Guards Black Finish
• SKU: MAG609
• Finish: Black
• Compatibility: M-LOK hand guards and Harris-style bipod studs

How the M-LOK Bipod Mount Installs

The Magpul M-LOK Bipod Mount slides into any M-LOK slot and locks in place using the M-LOK recoil lug system. This creates a rigid connection between the handguard and the mount. No Picatinny rail adapter is required.

M-LOK attachment hardware typically uses T-nuts and screws that tighten from the interior of the slot. Once installed, the mount sits flush with the handguard surface and provides a threaded stud boss for the bipod’s quick-detach lever.

Send us a message to confirm installation hardware included with this mount.

Why Choose a Direct M-LOK Mount Over a Rail Section

Adding a short Picatinny rail section to accept a bipod stud adds an extra layer of material, extra hardware, and extra weight. A direct M-LOK bipod mount eliminates that intermediate step.

This approach keeps the handguard profile cleaner and reduces the vertical height between the barrel centerline and the bipod legs. Shorter shooters and those using lower scope mounts often prefer the reduced stack height.

The mount works with any Harris-pattern bipod, including Atlas, Magpul, and many aftermarket models that use the same quick-detach interface.

What to Know Before Ordering

The Magpul M-LOK Bipod Mount requires an M-LOK handguard. It will not fit KeyMod slots or traditional Picatinny rails. Check your handguard for the narrow, rectangular M-LOK slot profile before ordering.

The black finish on this mount matches most anodized handguards and reduces reflection. For dimensions and torque specifications, contact us directly.

Ordering from Western Sport

Order online and it ships straight to your door. Western Sport has been a licensed FFL/SOT dealer since 2007, and everything we sell carries the full manufacturer warranty. Questions before you order? Send us a message.

Frequently Asked Questions

Q: Does the Magpul M-LOK Bipod Mount fit KeyMod handguards?

A: No, the Magpul M-LOK Bipod Mount fits only M-LOK slots. KeyMod and M-LOK use different slot geometry and are not interchangeable. You need an M-LOK handguard to use this mount.

Q: Will this mount work with Atlas bipods?

A: Yes, the Magpul M-LOK Bipod Mount accepts any bipod that uses the Harris-style swivel stud interface. Atlas bipods with the standard quick-detach lever attach directly to this mount.

Q: How many M-LOK slots does the MAG609 occupy?

A: Send us a message to confirm the slot length required for the MAG609. Slot count depends on the handguard’s M-LOK spacing and the mount’s footprint, which we can verify over the phone.

Q: Can I install the Magpul M-LOK Bipod Mount at the three o’clock or nine o’clock position?

A: Yes, M-LOK slots run along the sides and bottom of most handguards. You can install this mount at any position where M-LOK slots are present, allowing for angled or side-mounted bipod setups.

Q: What is the difference between this mount and a Picatinny rail section with a bipod stud?

A: The Magpul M-LOK Bipod Mount attaches the bipod stud directly to the M-LOK slot, eliminating the Picatinny rail layer. This reduces weight, stack height, and handguard bulk compared to a rail-mounted adapter.

Additional information